Skid Steers

Posts Tagged ‘bucket’

www.QuickSpadeS.com Greatest Bucket and Fork Attachment for Skid Steers or Bucket Loaders. Like a Tree Spade but fits on Bobcat Deere Gehl Toro Dingo Case ANY forks or buckets use to Trench Dig Haul

www.QuickSpadeS.com Greatest Bucket and Fork Attachment for Skid Steers or Bucket Loaders. Like a Tree Spade but fits on Bobcat Deere Gehl Toro Dingo Case ANY forks or buckets use to Trench Dig Haul

www.QuickSpadeS.com Greatest Bucket and Fork Attachment for Skid Steers or Bucket Loaders. Like a Tree Spade but fits on Bobcat Deere Gehl Toro Dingo Case ANY forks or buckets use to Trench Dig Haul

www.QuickSpadeS.com Greatest Bucket and Fork Attachment for Skid Steers or Bucket Loaders. Like a Tree Spade but fits on Bobcat Deere Gehl Toro Dingo Case ANY forks or buckets use to Trench Dig Haul

I designed and built this skidsteer from scratch to be easy to maintain and very durable. The frame and arms are 2×4 3/16″ tubing and the sides, bottom, and bucket are 1/4 plate steel. It weighs 1000 lbs. It can lift 500 lbs in its 4 ft bucket to about 61/2 ft high. It is four wheel drive using two hydraulic motors and a 13 hp engine. The engine runs a 16 gpm 2 stage log splitter pump. There are two 2/spool valve assemblies plumbed in parallel so it can lift and tilt at the same time or operate both drive motors at the same time. This is done with a dividing valve. It has electric start and recoil backup. I used trailer wheels because of the availability, low cost, descent load capacity, and good bite( they hook up well – I didn’t need floatation from a wider tire). I designed the drive hubs from trailer hubs for ease of service and reliability. The bucket was torch cut from plate steel and has a wear edge. The 10 gallon hydraulic oil tank was welded from 1/8″ sheet and it has brazed on pipe fittings for supply and return lines. The bucket and arm pins are 7/8 inch grade 8 bolts that rotate in 1′ steel tubing acting as bushings. The bushings are fit into 1″ schedule 80 pipe that has been drilled out slightly to recieve the 1″ tubing. I fit both of these “bushing housings” with grease zerks. I experimented with this design before and have found it inexpensive and tough. This way you can replace the busings as they wear. I have about 2500 dollars into the skidsteer from the …

www.QuickSpadeS.com Greatest Bucket and Fork Attachment for Skid Steers or Bucket Loaders. Like a Tree Spade but fits on Bobcat Deere Gehl Toro Dingo Case ANY forks or buckets use to Trench Dig Haul

www.QuickSpadeS.com Greatest Bucket and Fork Attachment for Skid Steers or Bucket Loaders. Like a Tree Spade but fits on Bobcat Deere Gehl Toro Dingo Case ANY forks or buckets use to Trench Dig Haul

Quick Attach Quick Clear Grapple Rod Bucket

www.QuickSpadeS.com 877-224-4899 SKID STEER FORK GRAPPLE ATTACHMENT loader for Bobcat Deere Gehl AVS skip the bucket! Grapple It for Skid Steer Fork Attachments – The Fork Grapple System is a one of a kind product that turns your standard skid steer forks into a fork grapple. With up to 7000 pounds of hydraulic pushing power and built from heavy gage steel. There is no job to big or too small for this product. You can move boulders, plant trees, remove trees, lift logs, remove tar, lift hay bails, demo projects and so much more. Just slide the Fork Grapple System onto your standard 4 wide skid steer forks, hook up your hydraulic lines and your ready to take on any size job. This product has saved contractors up to 6 hours of work time per job and has also reduce labor hours and work force up to 70%. This product is a dream come true for the logging, landscape, construction and the demo industry. So if you tired of having product roll of you forks or you need a system that complete any job. Then the Fork Grapple System is what you need. Order today and began saving time and money!! Visit http

Skid steer scrap magnet, side dump bucket, high rollout bucket, specialty grapples and hydraulic side tilt concrete bucket.